fbpx

製品情報

Winstar新製品 0.95インチ有機ELモジュール 96×64

型番 WEO009664A

►タイプ: グラフィック有機elモジュール (Without Frame)
►結構: COG
►サイズ: 0.95インチ
►96 x 64 ドットマトリックス
►SSD1305Zコントローラー内蔵
►3V電源電圧
►1/64 duty
►インターフェース: 6800, 8080, SPI, I2C
►発光色: 白色 / 黄色

製品情報

0.95インチのグラフィック有機ELモジュールWEO009664Aを発表致します。製品は96 x 64 ドットマトリックス 、SSD1305 ドライバーICを搭載して外形寸法は 24.90 x 22.95 mm。このサイズはウェアラブルデバイスに最適です。グラフィック有機EL・COGモジュールは超薄、軽量、低消費電力のメリットを有して、ハンドヘルド機器、メーター、スマートグリッド、ウェアラブル機器、IoTシステムなどに生かせます。また、COG構造製品はFPCが柔軟性を持って、FPCにチップが実装されずTAB構造の有機ELに比べたら曲げられることは対応可能です。そのため、客先側の設計制限が少なくなります。

外形図

 

製品仕様

 

ピン功能定義

Pin No. 記号 I/O 説明
1. N.C. (GND) Reserved Pin(Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2. VCC P Power Supply for OLED Panel
This is the most positive voltage supply pin of the chip.It must be supplied externally.
3. VSS P Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.
4. VDD P Power Supply for Logic Circuit
This is a voltage supply pin. It must be connected to external source.
5. VDDIO P Power supply for interface logic level.
It should be match with MCU interface voltage level. VDDIO must always be equal or lower than VDD.
6. BS1
BS2
I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:  

  68XX-parallel 80XX-parallel Serial I2C
BS1 0 1 0 1
BS2 1 1 0 0
7.
8. CS# I Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
9. RES# I Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10. D/C# I Data/ Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data. When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.
11. R/W# I Read/ Write Selector Write
This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XXinterface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
12. E/RD# I Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
13. D0~D7 I/O Host Data In put/ Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2Cmode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
14.
15.
16.
17.
18.
19.
20.
21. IREF I Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10μA.
22. VCOMH O Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
23. VCC P Power Supply for OLED Panel
This is the most positive voltage supply pin of the chip.It must be supplied externally.
24. VLSS P Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.
25. N.C. (GND) Reserved Pin(Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

規格説明

項目 仕様 単位
ドットマトリックス 96 x 64 Dots
モジュールサイズ 24.9 × 22.95 × 1.65 (mm) mm
アクティブエリア 19.946 × 13.418 (mm) mm
ドットサイズ 0.186 × 0.188 (mm) mm
ドットピッチ 0.208 × 0.21 (mm) mm
表示モード パッシブマトリクス
発光色 モノクロ
駆動方法 1/64 Duty
IC SSD1305Z

絶対最大定格

パラメーター 記号 最小値 最大値 単位
ロジック電源電圧 VDD -0.3 4 V
Display電源電圧 VCC 0 15 V
操作温度 TOP -40 +80 °C
保存温度 TSTG -40 +80 °C

電気特性

 

項目

記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VDD 2.8 3.0 3.3 V
Display電源電圧 VCC 11 12 13 V
高レベル入力電圧 VIH 0.8×VDD VDDIO V
低レベル入力電圧 VIL 0 0.2×VDD V
高レベル出力電圧 VOH 0.9×VDD VDDIO V
低レベル出力電圧 VOL 0 0.1×VDD V
50% Check Board operating Current ICC VCC=12V 5.8 6.0 7.5 mA

 

お問い合せはこちらから▶▶

関連記事

  1. この記事へのコメントはありません。

  1. この記事へのトラックバックはありません。

ピックアップ

  1. Winstar製品 5.6 インチ HD (高解像度) IPS ディスプレイ: eDP インターフェイス

  2. Winstar製品 8インチ垂直画面 800×1280 TFT-LCDディスプレイモジュール

  3. Winstar製品 800×1280 8インチ TFTタッチスクリーンディスプレイ (RTP)

  4. Winstar製品 800×1280 8インチ TFTタッチスクリーンディスプレイ (PCAP)

おすすめ記事

ページ上部へ戻る