fbpx

製品情報

Winstar新製品 1.54インチCOG OLED 静電容量式タッチパネル

型番 WEO012864A-CTP

►タイプ: グラフィック有機ELディスプレイ
►結構: COG
►サイズ: 1.54インチ
►128 x 64 ドットマトリックス
►SSD1309コントローラー内蔵
►3V電源電圧
►1/64 duty
►インターフェース: 6800,8080,SPI,I2C
►静電容量式タッチパネル(CTP)
►検出ポイント: 1
►発光色: 白色 / 黄色 / 緑色

製品情報

WEO012864A-CTPは解像度128×64ドットで構成されて、静電容量式タッチパネルが実装された1.54インチのCOG構造のグラフィックOLEDディスプレイです。SSD1309 ICが組み込まれて、800/8080 8ビットパラレルにして、4線式SPI及びI2Cインターフェイスを介して通信できます。ロジックの電源電圧は2.8V〜3.3Vで、標準値は3.0Vで、ディスプレイへの電源電圧は12.5Vで、駆動デューティが1/64です。タッチパネルICはMSG22SでI2Cインターフェイスで、1つの検出ポイントをサポートします。

CTPモデルを備えたWEO012864Aはスマートホームアプリケーション、インテリジェントテクノロジーデバイス、メーターデバイス、産業用制御システム、医療機器等に最適です。操作温度範囲が-10℃〜+60℃で、保存温度範囲が-20℃~+70℃です。

外形図

製品仕様

ピン功能定義

No. 記号 説明
1 NC(GND) No connection
2 VLSS This is an analog ground pin
3 VSS Ground.
4 NC No connection
5 VDD Power supply pin for core logic operation
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select

  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
11 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13-20 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
21 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 NC(GND) No connection

 CTP ピン功能

1 GND Ground
2 VDD Power Supply Voltage of CTP
3 RST External Reset, Low is active
4 INT External interrupt to the host
5 SCL I2C clock input
6 SDA I2C data input and output

規格説明

項目 仕様 単位
ドットマトリックス(解像度) 128 x 64
モジュールサイズ 43.04 × 28.22 × 3.01 mm
有効エリア 35.05 × 17.51 mm
ドットサイズ 0.249 × 0.249 mm
ドットピッチ 0.274 × 0.274 mm
表示モード パッシブマトリックス
発光色 モノクロ
駆動方法 1/64 Duty
IC SSD1309
インターフェイス 6800,8080,4-wire SPI,I2C
表示サイズ(対角線) 1.54 インチ
CTP IC MSG22S
検出ポイント 1
CTP インターフェイス I2C
表面処理 グレア

絶対最大定格

パラメーター 記号 最小値 最大値 単位
ロジック電源電圧 VDD -0.3 4 V
Display電源電圧 VCC 0 17 V
操作温度 TOP -10 +60 °C
保存温度 TSTG -20 +70 °C

 

タッチパネルコントローラー MSG22S

パラメーター 記号 最小値 最大値 単位
電源電圧 VDD 0 3.6 V

電気特性

DC電気特性

項目 記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VDD 2.8 3.0 3.3 V
Display電源電圧 VCC 12.0 12.5 13.0 V
高レベル入力 VIH 0.8×VDD V
低レベル入力 VIL 0.2×VDD V
高レベル出力 VOH 0.9×VDD V
低レベル出力 VOL 0.1×VDD V
50% Check Board operating Current VCC =12.5V 16 45 mA

 

タッチパネルコントローラー MSG22S

項目 記号 条件 最小値 典型値 最大値 単位
電源電圧 VDD 2.8 3.0 3.3 V
高レベル入力 VIH 1 V
低レベル入力 VIL 0.5 V
高レベル出力 VOH VDD-0.1 V
低レベル出力 VOL 0.1 V

関連記事

  1. この記事へのコメントはありません。

  1. この記事へのトラックバックはありません。

ピックアップ

  1. Winstar製品 5.6 インチ HD (高解像度) IPS ディスプレイ: eDP インターフェイス

  2. Winstar製品 8インチ垂直画面 800×1280 TFT-LCDディスプレイモジュール

  3. Winstar製品 800×1280 8インチ TFTタッチスクリーンディスプレイ (RTP)

  4. Winstar製品 800×1280 8インチ TFTタッチスクリーンディスプレイ (PCAP)

おすすめ記事

ページ上部へ戻る