fbpx

製品情報

Winstar新製品 5.5 インチ256×64 COF 有機EL PCB 基板+静電容量式タッチパネル

型番 WEN025664D-CTP

►タイプ: グラフィック有機ELモジュール
►結構: COF+FR+PCB
►サイズ: 5.5インチ
►256×64 ドットマトリックス
►SSD1322 コントローラー内蔵
►3V電源電圧
►1/64 duty cycle
►インターフェース: 6800, 8080, SPI
►静電容量式タッチパネル(CTP)
►検出ポイント: 1
►発光色: 黄色 / 緑色
►グレースケール機能をサポートする

製品情報

WEN025664D-CTPモジュールは産業用グレードで、5.5インチ COF構造の グラフィック有機EL ディスプレイです。 フレームベゼルと静電容量式タッチパネルを搭載しており、解像度は256×64です。SSD1322 COF ICを内蔵し、 6800/8080 8ビットのパラレルと 3線式/4線式SPIインターフェースをサポート致します。 グレースケールは4ビットで、ロジックの電源電圧は3Vで、50%チェックボード電流での表示は240mA @3.0V VDD (標準値)で、駆動デューティは 1/64です。 このモジュールは 静電容量式タッチパネルを搭載しており、 GT911 IC を内蔵し、 I2C インターフェースをサポート致します。 1本指で検出ポイントをサポートし、表面ガラスが通常のグレアタイプです。 そして、PCB基板を搭載しており、 お得意先の設備と製品に簡易に接続することができます。そして、PCB基板にVCC回路が設けられており、固定用の取り付け穴も付きのため 、お得意先の開発及び作業の効率を向上させます。このモジュールはピン、FFC、コネクタ、FPCなどの多くの配線方法もサポートしております。

基板に固定用の取り付け穴付きのため、簡単にお得意先の設備と製品に実装できます。 この有機ELディスプレイ はスマートホームアプリケーション、医療機器 、産業用制御システム などに適しております。操作温度範囲は-20 ℃ ∼ +70℃ で、保存温度範囲は-30℃ ∼+80℃です。

 

図 面

製品仕様

ピン功能定義

Pin Number 記号 I/O 説明
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:    

BS[1:0] Bus Interface Selection
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

規格説明

項目 仕様 単位
ドットマトリックス 256 × 64 Dots
モジュールサイズ 147.0 × 59 × 4.8 mm
アクティブエリア 135.65 × 33.89 mm
ドットサイズ 0.5 × 0.5 mm
ドットピッチ 0.53 × 0.53 mm
表示モード パッシブマトリクス
発光色 モノクロ
駆動方法 1/64 Duty
グレースケール 4 bits
OLED IC SSD1322
OLED インターフェイス 6800, 8080, SPI
表示サイズ(対角線) 5.5 インチ

 

CTP IC GT911
検出ポイント 1
CTP インターフェイス I2C
表面処理 グレア

絶対最大定格

パラメーター 記号 最小値 最大値 単位
顯示電源電圧 VDD -0.3 4 V
操作温度 TOP -20 +70 °C
保存温度 TSTG -30 +80 °C

電気特性

DC 電気特性

項目 記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VDD 2.8 3.0 3.3 V
高レベル入力 VIH 0.8×VDD VDD V
低レベル入力 VIL 0 0.2×VDD V
高レベル出力 VOH 0.9×VDD VDD V
低レベル出力 VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 240 400 mA

関連記事

  1. この記事へのコメントはありません。

  1. この記事へのトラックバックはありません。

ピックアップ

  1. Winstar製品 16×2キャラクタ UART 液晶 モジュール

  2. Winstar製品 16×2 UART LCD モジュール

  3. Winstar製品 20×2キャラクタ UART LCD モジュール

  4. Winstar製品 20×4キャラクタ UART LCDモジュール

おすすめ記事

ページ上部へ戻る