fbpx

製品情報

Winstar製品 1.5 インチ 128×128 グレースケール COG OLED モジュール

型番 WEO128128H

►タイプ: グラフィック有機ELディスプレイ
►結構: COG
►サイズ: 1.5 インチ
►128 x 128 ドットマトリックス
►CH1120コントローラー内蔵
►3V電源電圧
►1/128 duty
►インターフェース: 8080,SPI,I2C
►発光色: 白色/黄色

 

特 長

WEO128128H はグレースケール機能を備えた1.5 インチ COG グラフィック OLED ディスプレイです。解像度は 128×128ドットでCH1120 IC搭載で8080、SPI、I2C インターフェイス、1/128 駆動デューティをサポートいたします。ロジック電源電圧は 3V (VDD)でディスプレイ電源電圧は 12V です。そして、50% チェッカーボード表示での電流と言えば 20mA(白@ VCC 12V/黄@VCC 14.5V)です。WEO128128Hはスマート ホーム アプリケーション、クラウド/IoT システム、ハンドヘルド機器、インテリジェント テクノロジー デバイス、エネルギー システム、交通関係、通信システム、医療機器などに適しております。その動作温度範囲は-40℃ ~ +80℃で、保管温度範囲は-40℃~+85℃です。

図 面

製品仕様

ピン功能定義

No. 記号 説明
1 ESD_GND This pin should be connected to GND.
2 VPP This is the most positive voltage supply pin of the chip.
It should be supplied externally.
3 VCOMH This is a pin for the voltage output high level for common signals.
A capacitor should be connected between this pin and GND.
4 VDD Power supply for logic
5 NC No connection
6 IM1 These are the MPU interface mode select pins.

  8080 3-wire SPI 4-wire SPI I2C
IM1 1 0 0 1
IM2 1 1 0 0

These pins must be connected to “H” or “L”.

7 IM2
8 VSS Ground for logic and analog. This pin should be connected to GND externally.
9 IREF This is a segment current reference pin.
A resistor should be connected between this pin and GND.
10 CSB This pin is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
When in I2C interface, this pin is not used, so it must be connected to “L”.
11 RESB This is a reset signal input pin. When RESB is set to “L”, the settings are initialized. The reset operation is performed by the RESB signal level. This pin internal pull high.
12 A0 This is the Data/Command control pin that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pin serves as SA0 to distinguish the different address of OLED driver.
When in 3-wire interface, this pin is not used, so it must be connected to “L”.
13 WRB This is a MPU interface input pin.
When connected to an 8080 MPU, this is active LOW. This pin connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal
When in 3-wire.4-wire & I2C interface, this pin is not used, so it must be connected to “L”.
14 RDB This is a MPU interface input pin.
When connected to an 8080 series MPU, it is active LOW. This pin is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When in 3-wire.4-wire & I2C interface, this pin is not used, so it must be connected to “L”.
15 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface(SPI) and I2C is selected, then D0 serves as the serial clock input pin (SCL) and D1 serves as the serial data input pin (SI). At this time, D2 to D7 are set to high impedance. D7~D2 is recommended to connect the VDD or GND. It is also allowed to leave D7~D2 unconnected.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VPP This is the most positive voltage supply pin of the chip
It should be supplied externally.
24 ESD_GND This pin should be connected to GND.

規格説明

項目 仕様 単位
ドットマトリックス(解像度) 128 × 128 dots
モジュールサイズ 33.80 x 36.50 x 2.01 mm
有効エリア 26.86 x 26.86 mm
ドットサイズ 0.185 x 0.185 mm
ドットピッチ 0.210 x 0.210 mm
表示モード Passive Matrix
発光色 Monochrome
駆動方法 1/128 Duty
グレースケール 4 bits
IC CH1120
インターフェイス 8080,SPI,I2C
表示サイズ(対角線) 1.5 inch

絶対最大定格

パラメーター 記号 最小値 最大值 単位
ロジック電源電圧 VDD -0.3 3.5 V
Display電源電圧 VPP -0.3 15.0 V
操作温度 TOP -40 +80 °C
保存温度 TSTG -40 +85 °C

 

項目 記号 条件 最小値 典型值 最大值 単位
ロジック電源電圧 VDD 1.65 3.0 3.3 V
Display電源電圧 VPP 8.0 14.5 15.0 V
高レベル入力電圧 VIH 0.8×VDD VDD V
低レベル入力電圧 VIL GND 0.2×VDD V
高レベル出力電圧 VOH 0.8×VDD VDD V
低レベル出力電圧 VOL GND 0.1×VDD V
Display 50% Pixel on IPP VPP=14.5V 20 30 mA

 

関連記事

コメントは利用できません。

ピックアップ

  1. Winstar製品 5.6 インチ HD (高解像度) IPS ディスプレイ: eDP インターフェイス

  2. Winstar製品 8インチ垂直画面 800×1280 TFT-LCDディスプレイモジュール

  3. Winstar製品 800×1280 8インチ TFTタッチスクリーンディスプレイ (RTP)

  4. Winstar製品 800×1280 8インチ TFTタッチスクリーンディスプレイ (PCAP)

おすすめ記事

ページ上部へ戻る